Jump to content


Registered Member
  • Content Count

  • Joined

  • Last visited

  • Days Won


1jonathan1994 last won the day on March 7

1jonathan1994 had the most liked content!

Community Reputation

1 Neutral

About 1jonathan1994

  • Rank

Car Information

  • My Car
    2015 Taurus Limited 3.5na
  • Engine
    3.5 na

Profile Information

  • Actual Name
  • Gender
  • Location
  • Chapter
  1. I want to rig up a loss of coolant sensor for my 2015 3.5NA Taurus Limited in case I have water pump failure or leak as the water pump is internal and grenades the motor from hydraulic forces before the temperature gauge can go up. 1 Is the reservoir/pressure tank even the correct place for said sensor. When I drained the radiator, the tank never drained. After refilling, the coolant seemed to siphon out of the tank at a certain height. I wonder if the damage would be done with water pump failure before the tank lost enough antifreeze to trip a sensor. 2 Is there a better place the sensor on one of the lines near the thermostat? Or maybe a Large Tee in the upper radiator hose? 3 I have found some Amazon stainless steel GEM style sensors for cheap enough (long shaft with floating SS donut around shaft). Seems I could drill a hole in top of the reservoir and still retain use of my Pressure Cap. 4 I have seen where others use a plastic piece with a floating lever/bar. That means drilling a hole in the side of the tank below the water level. Not as appealing. 5 I thought about installing a Gems sensor in the (easily replaceable) cap, but then I would lose the 18psi pressure relief and have to add something in a hose (possible). 6 Should I tie in series with the oil pressure sensor so low water would show up as low oil pressure !!! to get the point across to whoever is driving? I see only one wire to the oil pressure sensor, so I am guessing it makes connection (signal current only) when there is pressure and is open when low pressure (fail safe). So if I put the coolant sensor in line in series, it would cut the signal. I have no idea how amps, volts, and resistance come into play here as I have no specs on the oil pressure switch circuit. 7 Can I just use the right side headlight for a power source to the switch then an audible amazon buzzer since its only on when the engine is running (Auto lights is always on). False signal or maintenance alarm could be silenced by cutting the lights off. The sensors want no more than 0.5A so It might mean a relay if I can’t find a buzzer with that low of a draw. An engine on key on power source would obviously be preferred.
  2. OP here So I tried 2 times to get my car looked at but everything is so busy the best they could offer was to leave it and they might get to it in a few hours…..I’m too busy to give up my car and bum rides that much. I often have to drive to another plant across town with no warning. So the ambient temp was 75F and I knew that was a sweet spot. So I decided to do it myself for the convenience. YES, I wanted to go to a pro as recommended but …LIFE. Ambient 76F. Vent temp on MAX AC is 60F. AC fan on low is 44F. Low side read 32psi with “AC PRO” nozzle – hey better than nothing. I don’t have gauges for High side L. Really not bad. Online chart says it should be 40-45psi low side. Added a 3oz bottle of PAG46 (actually 1oz 46, 1 oz mystery crap, 1 oz R134a). Since I soaked up the spilled oil with a few paper towels I figure this is plenty of oil. I estimate 1 oz after refilling the pan from a kitchen measuring cup of water to the same level as the oil lost. Then added part of a 12oz can of R134a but never could get the pressure to over 40psi. Also not sure how much went in as I later dumped the rest of that can in a Buick. Final result: Ambient 76F. Vent temp on MAX AC is 56F. AC fan on low is 41F. Low side read 39-40psi. 4F drop in MAC AC vent temp and 3F drop in AC temp on low fan. Time will tell if I estimated the amount of oil properly.
  3. I . GOOFED . BADLY .2 015 Taurus Limited, 3.5L. Doing the 100,000mi radiator flush (no chemicals and in the dark of night) and all online advice said the drain was on the driver’s side. All I can find is a hex plug (never seen one like that). So I turn it until I hear a hiss and small drip. Odd… I make sure I had the cap off the fill tank, then come back and give it a quick spin. A gush of vapor and fluid hits my arm and I REACT as if badly burned. Fumble…. and …throw…the wrench… then realized its actually COLD COLD COLD!!! 1 second later I realize my mistake and eventually fumble the wrench back in and tighten up the drain plug ….. for the condenser….SMH. I head gas balancing out in the system after I tightened the plug. Finished the flush but now I got a bigger problem. I lost quite a bit of gas and the catch pan had an ounce or two of green fluid (I’m guessing the oil). I know I’m banned from AC for a while so Ill either run full blast heat (HI) or turn the climate control off until I can get this fixed. I don’t know how much refrigerant I lost and how much was actually compressor oil. I have done my own AC work on cheap vehicles with success (AC PRO + Oil), but this is my “nicest” car ever so I don’t want to damage or goof up anything else. Obviously no air got in the system, but I’m definitely low on something. I have not turned the AC on to see if it’s cold or not. 1 Is it safe to drive as long as I don’t use the AC? 2 Is it safe to use the heat on HI? 3 Would much lubricant be in the condenser or was that green fluid just liquid state R134a that had not evaporated yet? 40degress F ambient temperature. Car was pointing steeply downhill and had been off from AC use for about 45 minutes. 4 I understand the AC cycle, am an engineer, but also understand I don’t have the tools to measure what I actually have left vs what I need (1.43lb R134a + 5.2oz oil per manual ). If the green fluid was just liquid state R-134a I should be able to just use a can of AC PRO. It was 40-45F outside. 5 Should I just eat the cost and take it to the dealership or a local shop? I’m guessing they would drain it and start over so they know what is in it.
  • Create New...